About This Item
- NEW 3-IN-1 TECHNOLOGY: When painting concrete, wood, stone or brick it primes, seals and protects with just two coats. For these bare substrates we recommend thinning the first coat by 20% with T0001 thinners, which acts as the primer/sealer.
- NON SLIP: This paint includes an aggregate mixed in, providing a rough textured finish that reduces the risk of slips.
- SUITABLE SUBSTRATES: Concrete, primed metal, wood, stone, brick.
- DRYING TIME: Touch dry in 2-4 hours, overcoat in 12-24 hours, full protection properties after 7 days, but the area can be walked on after 4 days.
- COVERAGE: Approximately 8 square metres per litre. This does not account for the method of application, absorption of substrate or wastage.
- APPLICATION: Apply by brush or solvent-resistant medium pile rollers.
- THINNERS: T0001 White Spirit.
- SHELF LIFE: 12 months.
Proudly manufactured in England by B.C. Paints Ltd. Please note that images and product titles are for advertising purposes only; tins are supplied in BC Paints logo cans or plain white cans for 0.5, 1, 2.5 and occasionally 5 litre sizes.
Application
Before starting, have your PPE ready, as our paint is oil-based and will not wash off easily with soap and water.
Ensure you have good ventilation to allow vapour to escape; ventilation is also necessary to maintain drying times. Without air movement, the coating won’t dry properly.
Be sure to stir the paint well before use.
Painting Over Existing Paint:
Step 1 - Preparation: Check the suitability of the product for the existing paint. We recommend trying a sample area first.
Step 2 - Clean and Abrade:
- Ensure the existing paint is in good condition prior to painting, then lightly abrade to provide a key for good intercoat adhesion.
- If there is flaking paint, it must be removed before painting.
- Ensure the substrate is dry and clean of any dirt, oil or grease.
Step 3 - Prime: This step is down to personal preference. Depending on the condition of the existing paint or if you are changing a dark colour to a light one, you may want to add one coat of primer.
If bare metal is showing you will need to spot prime with our metal primer, if there is rust this will need removing and spot priming.
Step 4 - Topcoat: Once you have completed the previous steps, 12-24 hours after applying the primer, you can add your first coat of topcoat. Wait another 12-24 hours before applying the second coat.
Two coats of top coat are recommended for optimal coverage.
Painting bare Concrete, Wood, Stone or Brick
Never pre-seal the floor prior to painting, particularly with latex or PVC sealers, as paint will not adhere properly.
New concrete floors should be left to dry for at least 3 months before painting. Any remaining moisture in the concrete can lead to paint delamination.
Step 1 - Clean and Prep: Ensure the substrate is dry and clean of any dirt, oil or grease. If there is any moisture in the substrate, it can cause delamination and lead to a loss of adhesion.
Step 2 -First Coat: For the first coat, we recommend using the standard smooth concrete Paint, as it’s easier to apply than the non-slip version. Thin the first coat by 20% with T0001 White Spirit to ensure the paint impregnates the substrate, this will act as the primer/sealer.
If you prefer to use the Non-Slip Paint for the first coat, the same 20% thinning applies.
Step 3 - Top coat: 12-24 hours after applying the first coat, you can apply the second coat of topcoat.
Two coats of top coat are recommended for optimal coverage.
Painting bare Metal
Step 1 - Clean and Prep: Ensure the substrate is dry and clean of any dirt, oil or grease. If there is any moisture on the substrate, it can cause delamination and lead to a loss of adhesion.
Step 2 - Prime:
Metal - If there is rust this will need removing and then priming with our High Build Zinc Phosphate Metal primer. If the substrate is exposed to harsh environmental factors, you can prime it with either Zinc Rich or our two-pack epoxy primer systems for optimal protection.
Step 3 - Top coat: Wait 12-24 hours after applying the primer before applying the first coat of topcoat. Then, after another 12-24 hours, apply the second coat.
Two coats of top coat are recommended for optimal coverage.
Primers
Metal - Single Pack Primer - High Build Zinc Phosphate Metal primer.
If the substrate is exposed to harsh environmental factors, you can prime it with either Zinc Rich or our two-pack epoxy primer systems for optimal protection.
Concrete, Wood, Stone or Brick: No primer is required, we recommend thinning the first coat by 20% to ensure it impregnates the substrate, this will act as the primer/sealer.
Mixing
Make sure to thoroughly stir the paint before application, as the aggregate can settle on the surface. If the non-slip component isn't mixed well, you'll end up with a thick concentration of it initially, causing uneven distribution—resulting in less non-slip texture as you use more of the paint.
- Use a mixer on a slow-running drill or a palette knife on smaller cans to mix the paint. An egg whisk, screwdriver, or small stick that doesn’t reach the bottom of the can is insufficient for proper mixing.
- Mixing should take place for 3-5 minutes.
- If you are adding thinners; they will need to be added once stirred.
Paint mixers are available to purchase. Click here to buy one.
Prime Colors
Black, BS 00 A 05 Goosewing Grey, BS 00 A 09 Mid Grey, BS 08 E 51 Yellow, BS 14 C 39 British Racing Green, BS 18 B 25 Grey, BS 18 E 53 Blue, BS 445 Tile Red, White
Size
5 litre, 2.5 litre, 1 litre
